Technical data:

• Dimensions:210mm x 120mm x 470mm (width x depth x height)
• Torch standard diameter: 32mm (other diameter on the basis of requirement)
• Standard range of torch vertical move: 150 mm (other range on the basis of requirement)
• Power supply: 24V DC

Additional Functions:

It secures an adjustment of correct height of the plasma torch above the cut material before the material piercing. The plasma head can find the material automatically by a contact and it will move to the required height.

Adjustable Force of Collision:

• it reacts to the collision equally in all directions
• Magnetic anti-collision system
• It prevents any damage of the plasma torch during run into material, or in case of cut piece
• jamming after cutting.

Extra function:

• Elimination of thin material bending during contact
• Detection of rusty plates and plates with scales
• Automatic voltage control of height
• It secures a maintaining of a correct height of the plasma torch above material during cutting.
• Automatic activation and deactivation depending on cutting speed
• Torch stroke at material piercing
• It is used for piercing of thick plates. Torch stroke protects consumable materials against melted metal.
• Torch drop after the material piercing
• It secures an immediate shift of the torch to the cutting height after the material piercing.
• It is used for cutting of small holes for under chamfering elimination.
• Pneumatic anti-collision system
• It prevents any damage of the plasma torch during run into material, or in case of cut piece jamming after cutting.

Color touch display:

Ten-year s experience with touch screens has shown that such communication between the control system and operator is now the fastest and the most comfortable solution. The industrial version guarantees its long endurance and high reliability even under extremely dusty environmental and climatic conditions. The basic prerequisite for comfortable operation is a suitable software interface with large enough controls and clear screen. That was the most important factor in development of this control system. A great benefit from the viewpoint of the service life and maintenance is absence of mechanical push-buttons and controls.

Communication interface:

The communication interface helps the operator in an intelligible and intuitive way in preparation of cutting and during the process. Each screen of the machine can be adapted to the particular specification of the machine and to the currently used technology. This fact together with logical succession of separate steps of the control process makes the system very simple for training operators. Large controls make the operative control even easier using a touch display. That system can be used all over the world thanks to unambiguous images of the controls together with different language versions of legends and reports.

Clear graphic interface:

The system screen is clearly divided into four parts:

Status bar – it shows the current position of the machine in X and Y axes, current date and time and report on the machine condition. Different conditions of the machine are highlighted by changed color of the window for better orientation of the operator.

Main window – it changes depending on the work which is being done and current state of the control system.It us used for entering parameters and setting the whole system

Tool panel – it is used for operating tools, above all, cutting heads. The appearance of the panel changes during work depending on the selected technology.

Control panel – it is used for automatic and manual control of the machine. The appearance of the window does not change during work so that the most important controls of the system could be accessed immediately.

Two sizes of the screen – 15“ and 19“

• 15“ – economical version suitable for smaller machines and applications. It just has small dimensions, but not lower Performance and worse software.
• 19“ – explicit and large display provides very transparent and comfortable operation with a detailed view of the graphic part of the screen.

Manual gas console with manual piercing of material and high pre-heating Hi-Low:

• Regulator for adjustment of pre-heating gas pressure (acetylene, propane, natural gas)
• Regulator for adjustment of pre-heating oxygen pressure
• Regulator for adjustment of cutting oxygen pressure
• Manual piercing valve
• 3 solenoid valves for the start of gas standard pressures
• 2 solenoid valves for the start of high pressures of preheating oxygen and gas (high pressure for preheating is adjusted on the regulators of gas bottles)

Manual gas console with automatic two-stage piercing of material:

• Regulator for adjustment of pre-heating gas pressure (acetylene, propane, natural gas)
• Regulator for adjustment of pre-heating oxygen pressure
• 2 regulators for adjustment of cutting oxygen pressure (material piercing is carried out in two automatically controlled stages)
• 3 solenoid valves for the start of gas standard pressures
• 2 solenoid valves for the start of high pressures of preheating oxygen and gas (high pressure for preheating is adjusted on the regulators of gas bottles)

Manual gas console with automatic four-stage piercing of material:

• Regulator for adjustment of standard (low) pressure of preheating gas (acetylene, propane, natural gas)
• Regulator for adjustment of standard (low) pressure of preheating oxygen
• Regulator for adjustment of high (Hi) pressure of preheating gas (acetylene, propane, natural gas)
• Regulator for adjustment of standard (low) pressure of preheating oxygen
• Regulator for adjustment of high (Hi) pressure of preheating oxygen
• 4 regulators for adjustment of cutting oxygen pressure ( material piercing is carried out in four automatically controlled stages)
• 2 solenoid valves for the start of standard pressures of preheating oxygen and gas.
• 2 solenoid valves for the start of high pressures of preheating oxygen and gas (high pressure for preheating is adjusted on the regulators of gas bottles)
• 4 solenoid valves for the start of 4 stages of cutting oxygen